5W Portable Solar Panel Kit System 3W LED Light Bulbs USB Sales

Introduction
1,The solar lantern(camping light)mainly use solar and energy-saving LED of technology, delicate appearance, using convenient and simple operation, and built-in lead-acid battery, can use sunlight charging. At the same time also can choose the AC adapter, when no sunlight can be used to charging.
2,The product is equipped with status indication, USB adapter for charging the mobile phone, multi-position lighting choose, etc. It suitable for home lighting, outdoor camping, yurts, tents and other outdoor and indoor lighting, drivers drive, more safety, high efficiency, energy saving, environmental protection.

Parameters
 
Attention
1,Please read the instruction before use.
2,Long time no use , please turn off the power.
3,Charging more than 10 hours every3 months.
4,Don't use other adapter and solar panel charger this product.
5,Don't open the panel and battery.
6,Light stay away from water, combustible gas and etchant.
7,The temperature keep between 0ºC-40ºC.

Instruction

1. Please full charge battery first using. (When charging the red light flashing , after fully charged battery indicator light change green and continuous on)The brightness have four levels:  50% brightness,  75% brightness 100% brightness 25% brightness.Through the standard USB cable can be directly connected to the 5v output charge for mobile phone, game consoles, digital cameras, MP4 and other small capacity equipment.Plug the standard LED bulb into DC1 ~ DC4 any hole, then switch on bulb.

Operation

1. If use solar panel charging, first insert the solar panel into the DC charger,put solar panels on enough sunny places, pay attention to not have anything blocking solar panels.Using AC charging, put the adapter DC into solar light DC charger,then connect the charger with 220 VAC.

 Fault
1,Don't charger battery but the red light flash mean the battery voltage too low, it need connect the solar panel or adapter to charge, when full charger it will eliminated this fault.
2 ,The red light is not flash and green light is not bright when charging, you can check DC plug whether connected, panel whether have enough sunlight.



 








Introduction
1,The solar lantern(camping light)mainly use solar and energy-saving LED of technology, delicate appearance, using convenient and simple operation, and built-in lead-acid battery, can use sunlight charging. At the same time also can choose the AC adapter, when no sunlight can be used to charging.
2,The product is equipped with status indication, USB adapter for charging the mobile phone, multi-position lighting choose, etc. It suitable for home lighting, outdoor camping, yurts, tents and other outdoor and indoor lighting, drivers drive, more safety, high efficiency, energy saving, environmental protection.

Parameters
 
Attention
1,Please read the instruction before use.
2,Long time no use , please turn off the power.
3,Charging more than 10 hours every3 months.
4,Don't use other adapter and solar panel charger this product.
5,Don't open the panel and battery.
6,Light stay away from water, combustible gas and etchant.
7,The temperature keep between 0ºC-40ºC.

Instruction

1. Please full charge battery first using. (When charging the red light flashing , after fully charged battery indicator light change green and continuous on)The brightness have four levels:  50% brightness,  75% brightness 100% brightness 25% brightness.Through the standard USB cable can be directly connected to the 5v output charge for mobile phone, game consoles, digital cameras, MP4 and other small capacity equipment.Plug the standard LED bulb into DC1 ~ DC4 any hole, then switch on bulb.

Operation

1. If use solar panel charging, first insert the solar panel into the DC charger,put solar panels on enough sunny places, pay attention to not have anything blocking solar panels.Using AC charging, put the adapter DC into solar light DC charger,then connect the charger with 220 VAC.

 Fault
1,Don't charger battery but the red light flash mean the battery voltage too low, it need connect the solar panel or adapter to charge, when full charger it will eliminated this fault.
2 ,The red light is not flash and green light is not bright when charging, you can check DC plug whether connected, panel whether have enough sunlight.



 

Linear Encoder

Draw-wire sensors of the wire sensor series measure with high linearity across the entire measuring range and are used for distance and position measurements of 100mm up to 20,000mm. Draw-wire sensors from LANDER are ideal for integration and subsequent assembly in serial OEM applications, e.g., in medical devices, lifts, conveyors and automotive engineering.

Linear Encoder,Digital Linear Encoder,Draw Wire Sensor,1500Mm Linear Encoder

Jilin Lander Intelligent Technology Co., Ltd , https://www.jllandertech.com