In September 2015, LZ bought a 360 child guardian phone watch 3rd generation as a birthday gift for her daughter. At that time, he still had to hunger for the hungry marketing practices on the official website. Very bs, but princess ordered, can only win desperately, 399 yuan official website price.
One year later, the day before yesterday suddenly discovered how the watch can not be charged, the magnetic back of the watch before the charge is also found that the contact is a bit bad, and sometimes it takes a few times to charge, but this time it is how can not press the charge. So I took a 360 children’s watch bought by my friend’s and conducted a replacement method to see if it’s a problem with the charging cable or the watch’s own problems. As a result, my watch can be charged with his charging cable, and my charging cable is also His watch can be charged, but my charging line is unable to charge my watch. There are a few swear words.
Baidu later about 360 watch can not be charged and found that many people have encountered such problems, all in the Tucao 360 this product's charging design flaws, some people can not recharge after 3 months to buy a watch, some are six months , Like me it happens to be a little more than a year, but also after the warranty period (I do not know whether the charging line has a warranty period).
How to do? How to do? ? Philosophy teachers at the university said that we must develop people’s subjective initiative. Although I still cannot understand the specific meaning of this sentence, I already know that everything depends on my own reasoning. So after I basically decided that the charging line was in contact, I started to unravel the charging connector. In fact, it was violent dismantling. After using a knife to open it like this:
Then I directly held the end of the watch with four metal contact points, indicating that the battery is charging at a current of 0.2 A. This further proves the problem of poor contact.
Then I put the original plastic sheet, and then connected the charging head, and found that no matter how tight, it can not be charged.
Now that it is judged that with this gasket, the metal contact point is not touched and naturally cannot be charged. I do not know why this charging connector will cause such problems after a while. Now my solution is to polish and cut out the plastic around the metal contact point of the original plastic gasket, so that the charging interface is more closely contacted.
Because the plastic gasket is relatively small, it is difficult to hold down, and the props have to be forced when cutting, the fingers are also cut, do not know if it will affect my fingerprint unlock, but here you can reward.
After polishing, look at the contrast maps before and after, and the entire circle of raised plastic is almost invisible.
At this time, try again, press and hold it and find that it can be charged, and the current display is 0.21A.
Now we must assemble it back. Because the original violent dismantling has not been able to completely restore the charging head, only the practice of a little cottage, which plug a little newspaper so that the interior is full, and then put two small magnets embedded in, pay attention to Polarity, because I just installed it and discovered that the magnets on the watch side are mutually exclusive. As a result, the swapped position changes again when they are removed again.
Finally, use transparent glue to temporarily wrap it around. You can also try to seal it with adhesive. However, it is not recommended to do so. If you need to dismantle, you must make great efforts.
Well, the last is to check the actual use of the effect, and affixed to the back of the watch, as usual, can automatically absorb, do not press long fingers.
Let's take a look at the charging current and it shows 0.2A charging and it's done! ! !
Applause sounded. . .
Summary: If any valued friend also bought this product, and found that it can not be charged, you can first try my method, and do not use brute force to crack, just need to use a blade to cut off around the four charge points Plastic can be. Be careful not to scratch! !
In addition, if you feel that you have poor hands-on skills, you can go and search Ma Yunjia separately to buy a charging cable, but I have read comments that I cannot charge for a while.
Vecsel Experimental System,Chip Testing System Certification,Chip Testing System Chart ,Chip Test Requirements
AcePhotonics Co.,Ltd. , https://www.cgphotonics.com